Summer Starts Here - Save up to 70%
Curt Powered Tail Light Converter Installation - 2023 Chrysler Pacifica- Video
Hey everyone, Ryan here at etrailer. Today under 2023 Chrysler Pacifica we're gonna be showing you how to install the CURT Custom Fit Wiring Kit. But before we get into that, let's take a few minutes, check this out and make sure it's gonna work for you. So with these Pacifica's, you know, people use 'em to do a lot of different things. They're pretty capable vehicles and you'll see people using 'em to pull their trailers around and if you plan on doing that, you're gonna need a way to illuminate all the lights on that trailer. That way you're not only safe but it's a legal requirement as well. more
12/20/2023 8:33:28 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2020 Chrysler Pacifica- Video
Hey everyone, Ryan here at Etrailer. Today on our 2020 Chrysler Pacifica, we're gonna be showing you how to install the Curt Custom Fit Trailer wiring harness. Before we do that though, let's take a minute, check it out and make sure it's gonna work for you. When it comes to these Pacifica, you know they're extremely capable vehicles and so people do a lot of different things with them and that does include pulling some trailers around and if that's what you plan on doing, you need a way to illuminate the lights on that trailer. That way you're not only safe but legal as well. And that's exactly where this trailer wiring's gonna come into play. more
11/3/2023 1:40:09 PM
Curt Powered Tail Light Converter Installation - 2023 Chrysler Pacifica C59236- Video
All right, John with etrailer. If you're wanting to add trailer wiring to your Pacifica, then check out this option we have here. And this is the CURT Powered Converter Trailer Wiring Kit, and we've installed this on our 2023 Chrysler Pacifica. Now, this kit is gonna give you one of the most popular connectors, the four-way flat. This gives you your basic lighting functions. This is gonna give you left and right turn signal, brake lights, and tail marker lights. more
8/23/2023 10:10:41 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2019 Chrysler Pacifica- Video
Hey guys, this is Jake here with etrailer. Today we have a 2019 Chrysler Pacifica, and we're gonna be walking you through and showing you how to install The Curt 4-Pole wiring harness. Installing a 4-Pole wiring harness is gonna allow you to connect to a trailer to signal other motorists what your intentions are when you're pulling a trailer. This wiring harness is going to connect directly into the back of your factory taillights on your Pacifica, and it's gonna have a converter box on it that's designed to protect the vehicle from any back feed that might come from your trailer. So if you have a short or something on your trailer, it's not going to affect your vehicle's lights from functioning. A nice part about this kit is you're not gonna have to tap into any of your vehicle's wiring. more
4/28/2023 11:25:03 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2022 Chrysler Pacifica- Video
Hello neighbors, it's Brad here at etrailer and today we're taking a look and installing the curt four-pole trailer wiring harness on a 2022 Chrysler Pacifica. Now four-pole wiring is gonna be essential if you plan on towing a trailer and a lot of accessories these days will have lights on them that you're gonna get those lighting functions from your four-pole. And this just simply goes back into a module where those wires tie off and plug in directly to your taillights. So that way there's really no cutting or splicing that's required when plugging in. Now you are gonna have to run a power wire up to the front to get that 12 volt power supply but really that's not too terribly bad. It comes with all the butt connectors to be able to do that and it's minimal. more
10/25/2022 4:10:12 PM
Hopkins Plug-In Simple Vehicle Wiring Harness Installation - 2013 Chrysler Town and Country- Video
Hello neighbors. It's Brad here at etrailer, and today we're taking a look at installing the Hopkins 4-Pole Trailer Wiring on a 2013 Chrysler Town and Country. Having a hitch is great because you can hook up a lot of different accessories including trailers, and part of towing a trailer is making sure you have the proper light functions. That way when you have your headlights on, or your brake signal, or even your turn signal, you're gonna let the people behind you know what you're actually doing. And that's accomplished by installing a trailer wiring harness, such as this four flat. Now this is gonna be great to just plug into your trailer and it uses factory style connectors into your taillights so you'll be able to get all those functions pretty easy. more
6/1/2022 12:34:52 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2000 Chrysler Town and Country- Video
Hi everybody. My name is Andy with the etrailer. And today we're gonna install a Tekonsha four-pole flat wiring harness on this 2000 Chrysler Town & Country. We're gonna walk you through the installation process. So this four-pole flat wiring harness will allow you to communicate your lighting functions to whatever you'll be towing behind your vehicle. So what's nice about this particular wiring harness from Tekonsha is that it does have a converter box. more
11/9/2021 2:04:10 PM
Curt T-Connector Vehicle Wiring Harness Installation - 2021 Chrysler Pacifica- Video
Hey everyone, Shane here with etrailer.com. Today, I have a 2021 Chrysler Pacifica, and I wanna walk you through how to install the CURT Custom Vehicle Wiring Harness with four-pole flat trailer connector. This is what it's gonna look like when it's installed. The kit does not come with this four-pole bracket, however, you can pick one up here etrailer to give your wiring a more permanent mounting location. The wiring harness is designed to give your trailer the proper lighting functions so your legal and safe, brake signal, turn signals and your running lights. It's gonna come with a nice dust cap, so when you're not using it, it will keep any dirt and debris off the plug itself. more
9/1/2021 6:12:57 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2020 Chrysler Pacifica C56399- Video
Today, we're going to be going over and showing you how to install the Curt T-connector wiring harness here on the 2020 Chrysler Pacifica. The only thing we're going to be able to see from this kit here is the actual trailer connector. Now there's a couple of different means of attaching this. We can purchase a series of brackets here through etrailer to permanently attach it to the hitch tube. However, we can just use the included dust cap to loop it around the safety chain loops which is going to be the most economical option. So if you're going to be towing a trailer with your Pacifica, you will need a trailer wiring harness. more
5/28/2021 6:34:36 AM
Hopkins Plug-In Simple Vehicle Wiring Harness Installation - 2014 Chrysler Town and Country- Video
Hey everybody. How's it going Clayton here at etrailer.com. Here at eTrailer we install, test, and review a lot of different products to help you as a customer make a more educated decision before your purchase. Today we're going to be working on a 2014 Chrysler Town & Country. We're going to be taking a look at and I'll be walking you through how to install the Hopkins Simple Plug & Play 4-Pole Wiring Harness. This is what our 4-pole harness is going to look like installed. more
3/12/2021 1:14:21 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2020 Chrysler Pacifica- Video
Ryan: Hello, I'm Ryan and here at etrailer, I test fit, install and review a lot of different products to help you with any questions that you might have. So today on our 2020 Chrysler Pacifica, we're going to be taking a look at and showing you how to install the Tekonsha T-One Vehicle Wiring Harness. So these Pacificas are really versatile vans and people use them to do a little bit of everything, which that does include towing. And possibly some of you may have some light up accessories like a cargo carrier, for example. And that's where our wiring is going to come into play.Not only will it power up those light up accessories, but it'll also eliminate the lights on our trailer. That way whenever we're going down the road, we'll not only be safe, but legal as well. more
10/8/2020 10:37:11 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2017 Chrysler Pacifica- Video
Hi there Chrysler owners. Today in your 2017 Chrysler Pacifica, we're going to be taking a look at and showing you how to install CURT's four pole flat trailer connector vehicle wiring harness. You'll have a four pole connector that's outside the vehicle here at the back. We do offer mounting brackets here at etrailer.com. Our customer didn't opt for it, but many hitches do have weld plates on them that allows you to attach it directly to a bracket here. We just use a zip tie because that's what comes included with the kit and it'll work just fine. more
8/13/2020 3:01:28 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2019 Chrysler Pacifica- Video
Rob: Everybody Rob here at etrailer.com today we're going to be taking a look at the inaudible 00:00:04 T-ONE vehicle wiring harness on our 2019 Chrysler Pacifica. Now, our T-ONE vehicle wiring harness is going to provide us with a 4-pole flat trailer connector. So whenever we're towing our trailer down the road, we can be safe and legal because it's going to give us our tail signals, turn signals, and our brake lights signals.Now, we'll use this 4 pole braker to Mount up our wiring. It's going to give us a nice clean appearance to it, but it's also going to make sure that our wiring is nice and secure and ready for us whenever we want to. Now, the brake does not come with the wiring, but you can find it here at etrailer.com. Our wiring is not going to be just for trailers. more
12/19/2019 2:12:17 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2013 Chrysler 200- Video
Hi, there 200 owners. Today on your 2013 Chrysler 200, we're going to be taking a look at and showing you how to install Tekonsha's T-One Vehicle Wiring Harness with Four Pole Flat Trailer Connector.Now, this is what our wiring looks like when it's installed. It's stored outside the vehicle. A great way to store it when you're not using it is to use the included dust cap to secure it to your trailer hitches safety chain loop. There are brackets also available here at etrailer.com to make it even nicer and neater. This harness will provide you with all the necessary lighting, keep you DOT compliant in all states. more
8/21/2019 3:57:56 PM
Curt Wiring Harness Installation - 2011 Chrysler Town and Country- Video
Shane: Hi, I'm Shane with etrailer.com. Today you're going to be taking a look at, I'm going to walk you through the installation on the Curt Wiring Harness with four pole flat trailer connector, on our 2011 Chrysler Town and Country. Whether you're hauling a trailer or a cargo carrier that may handle some lighting functions, this wiring harness is going to allow your trailer and cargo carrier to receive those lighting functions from your vehicle.Our Curt Wiring Harness is going to have a converter box, and what that converter box is going to do, it's going to protect the factory wiring on your vehicle from any back feed from your trailer if there is a wiring issue. Our four pole connection is going to give us all our proper lighting functions on our trailer. It's going to use our brake signals, our turn signals, and our running lights.It's also going to have a nice attached dust cap that's going to protect our connections from any dirt and debris when not in use, and it can double as a holder to help keep your wiring from dragging the ground. it's gonna give us three amps per circuit for our stop and turn signals, and six amps per circuit for our tail lights, which means if we have a trailer that may have some extra lighting on it, we know that our wiring is going to be able to handle it.Now that we've gone over some features, we'll show you how to get it installed. more
4/30/2019 4:52:12 PM
Curt Wiring Harness Installation - 2016 Chrysler Town and Country- Video
Today on our 2016 Chrysler Town & Country, you're going to be taking a look at, and I'm going to show you how to install the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector. This is what our wiring looks like when it's installed. This is going to give us all the proper lighting functions to safely tow our trailer: both turn signals, our brake lights, and our running lights. We're going to have a nice attached dust cap that's going to help protect our connections from any dirt and debris when not in use. The dust cap can also second as a holder when not in use. It's going to help keep our wiring from dragging the ground.It's going to give us three amps per circuit for stop and turn signal, six amps per circuit for our tail lights. more
3/18/2019 5:27:11 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2013 Chrysler 300- Video
Today on our 2013 Chrysler 300, we're going to be taking a look at, and showing you how to install the Tekonsha T1 Vehicle Wiring Harness with four pole flat trailer connector, part number 118600.This is what our wiring is going to look like when it's installed. This is going to give us all of our proper lighting functions to safely flat tow our trailer. We're going to get both turn signals, our running lights, brake lights, and our ground. It's also going to come with a nice attached dust cap. It's going to help keep any dirt and debris from getting on our connection points. This wiring harness is made to live inside of the vehicle, so when not in use simply just roll it up and you can store it right down into your spare tire area. more
1/14/2019 11:47:13 AM
Tekonsha T-One Vehicle Wiring Harness Installation - 2018 Chrysler Pacifica- Video
Speaker 1: Today on our 2018 Chrysler Pacifica, we're gonna be installing Tekonsha's T-One four-pole flat trailer connector vehicle wiring harness, part number 118712.This four-pole vehicle wiring harness is gonna provide you with all the necessary connections you'll need at your trailer. This is gonna give you your left turn signal, right turn signal, tail lamps, and brake lamps. So you'll be DOT-compliant in all states.At the back of our four-pole connector, you're gonna have a dust cap that'll keep out any dirt, debris, and moisture, and this'll ensure you have a long-lasting connection that'll be corrosion-free.In addition, you can use it to secure it to your safety chain loop and that'll hold it up out of the way when you're not using it.This wiring harness is custom-fit for your Pacifica. It's gonna plug directly inline with your driver and passenger side tail lamp assemblies. And it has its own module that's going to detect those signals and return them, here, to our four-pole connector, going back to your trailer.What's nice about this separate fuse-protecting circuit that our module has is that if there's any faults on our trailer, it won't cause any damage to the wiring on our vehicle. It'll just open the fuse to our module. more
11/30/2018 9:52:51 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2018 Chrysler Pacifica- Video
Speaker 1: Today on our 2018 Chrysler Pacifica, we're going to be taking a look at, I'm going to show you how to install, the Curt T-Connector vehicle wiring harness with 4-pole flat trailer connect. Part number C56322. Here's what you're going to get in your kit. You're going to get your wiring harness. Going to give you yours plugs that are going to plug into existing wiring. This is going to be for your passenger side. more
10/29/2018 1:28:36 PM
Curt Wiring Harness Installation - 2014 Chrysler Town and Country- Video
Speaker 1: Today on our 2014 Chrysler Town and Country, we're gonna be installing Curtz' T-Connector Vehicle Wiring Harness with four pole flat trailer connector. Part number C56331. This 4 pole flat trailer connector's gonna provide you with all of the necessary lighting. This includes your left turn signal, right turn signal, tail lamp and brake lamps. So you'll be DOT compliant in all states.This harness has it's own separate control module that's going to tap into your existing rear tail lamps to get the signals, and it'll provide those signals from the module to your connector. What's nice about this is that that module has its own fuse-protected circuit, so if there's any faults on your trailer such as a short, it'll only affect the circuit going to your module, and not anything on your vehicle.It also has an included dust cap. more
9/25/2018 7:47:35 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2008 Chrysler Pacifica- Video
Speaker 1: Today on our 2008 Chrysler Pacifica, we'll be having a look at and installing the Curt T connector vehicle wiring harness with four pole flat trailer connector. Part number C55530. Here's what our wiring looks like installed. As you can see, it's designed to be hidden in our storage compartment in the back of our vehicle when it's not in use. When we're ready to use it, we simply grab it from the storage compartment here, drape down some of the wire, lay it atop the weather stripping seal of our rear hatch, making sure it's to the side of our latch. And we can close our hatch on up. more
1/18/2018 1:20:34 PM
Tekonsha T-One Vehicle Wiring Harness Installation - 2017 Chrysler Pacifica- Video
Speaker 1: Today on our 2017 Chrysler Pacifica, we're gonna take a look at and also show you how to install the Tekonsha T-One Vehicle Wiring Harness with the 4-Pole Flat Trailer Connector. Part number is: 118712. Now, the T-One Vehicle Wiring Harness is gonna be exactly what you need to have a 4-pole flat trailer connector on the back of your vehicle. Looks like we've got a dust plug there. This is gonna take care of your right turn and brake, left turn and brake, running lights, and the bare terminal there is gonna be for ground, dust terminal to cover that up. But this is gonna work out really well for cargo carriers or any other trailer that has a 4-flat connector.Now, powering the system is gonna be our module box. more
10/2/2017 2:29:10 PM
Curt Wiring Harness Installation - 2013 Chrysler Town and Country- Video
Speaker 1: Today on our 2013 Chrysler Town & Country we'll be having a look at and showing you how to install the Curt T-connector wiring harness with a four-pole flat trailer connector. Part number C56331.This wiring harness is fairly unique in the regards that we have a nice module here that is nice and sealed from the elements with this silicone gel insert in here that prevents any moisture or contamination from getting inside causing corrosion or possible damage to the sensitive electronics inside.The reason this box is a great thing to have is because this will isolate your vehicle's expensive lighting circuit from your trailer. So if you have a short on your trailer you don't have to worry about any voltage being back-fed into your Town & Country causing potential damage.Here's what our wiring looks like installed. This four-pole flat wiring harness will give us the basic lighting functions that are required by law in order for us to safely and legally tow a trailer.This white wire here provides our necessary ground connection between our Town & Country and our trailer. This brown wire here is for our taillight and our running light circuit. And on this circuit we will have six amps of total power output, which is more than adequate to tow a trailer with a few incandescent light bulbs, probably can run as many LED light bulbs as you want, because they do draw less power.The yellow wire is for our left turn signal and left brake light. more
9/27/2017 11:53:54 AM
Curt T-Connector Vehicle Wiring Harness Installation - 2017 Chrysler 300C- Video
Today on our 2017 Chrysler 300C, we're going to be taking a look at and showing you how to install the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56235. This is what our wire looks like when it's installed. You can see it's going to live inside the vehicle. This is going to provide you the necessary power to light your trailer. You're going to have three amps per circuit for your stop and turn signals. You're going to has six amps per circuit for your tail lights. When you're not in use, you just simply take it, roll it up. more
7/17/2017 9:14:47 AM
Trailer Wiring Harness Installation - 2016 Chrysler Town and Country- Video
Today on our 2016 Chrysler Town & Country, we're going to be taking a look at and installing the Tekonsha T-One vehicle wiring harness with 4-pole flat trailer connector - part number 118534. Here's what our wiring is going to look like when installed on the vehicle. This wiring harness is going to work very well for all of your applications that are gonna need to connect to a 4-pole harness. It has a power module box which is gonna help give you plenty of power here, but it's also gonna help to separate this system from the vehicle's electrical system. So that way you don't risk the same type of damage you would if you just wired in directly. It also has T-connectors that go into the factory connections at the rear of the taillights, which are gonna make it easier for installation. Now, let's go ahead and show you how to install this wiring. Here's everything that's gonna come with our kit. more
12/9/2016 11:49:41 AM
Trailer Wiring Harness Installation - 2017 Chrysler Pacifica- Video
Today on our 2017 Chrysler Pacifica, we're going to take a look at and also show you how to install the Tekonsha T-One Vehicle Wiring Harness with the 4-pole Flat Trailer connector. Part number is 118723. Now, this is going to deliver 4.2 amps per side, for our stop and for our turn signals. For taillights, we have 7.5 amps. This should be plenty to power any standard size trailer lights. This is what our wiring kit is going to look like when we lay it out. This is our main goal here. This is what we're after, to have a working 4-pole trailer connector at the rear of our vehicle. Now, this is going to give us our right turning brake, our left turning brake, running lights and also the ground for our trailer. more
11/16/2016 4:56:47 PM
Trailer Wiring Harness Installation - 2016 Chrysler Town and Country C56150- Video
Today on this 2016 Chrysler Town and Country we're going to review and install Curt T-Connector Vehicle wiring harness with a 4-pull flat trailer connector, part number C56150. All right, this is what our wire harness looks like when it's installed on our van. Of course, there's not much to see right here but here's our 4-pull slat right here with the included cap. Now a good application for this would be any small trailer that has 2 or 4 running lights on the side of the trailer and a couple of tail lights in the back. That would be more than adequate for this type of system that we have on our van here. Now our part here is also good for insulating the wire harness from your trailer to your vehicle to minimize any damage as well. The installation onto a factory wire harness, where needed, does not require any splicing due to it's built in t-connectors. This does require a power ramp and a battery for a 12 volt supply and that's how it get's it's power to run the trailer. more
7/18/2016 5:27:32 PM
Trailer Wiring Harness Installation - 2006 Chrysler Town and Country- Video
Today on our 2006 Chrysler Town and Country we'll be installing the tow-ready T1 vehicle wiring harness with 4-pole flat trailer connector, part number 118300. The tow-ready wiring harness for our Town and Country stores easily out of sight and out of mind when not in use. To gain access to it, we just remove our jack storage cover here and we'll pull out our wiring harness, set it down here next to our latch for our tailgate on our van and we can shut it just like so. It's easily accessible now so we can hook up our trailer and I have this nice included dust cap here. This will work with any trailer that has a 4-pin flat connector. We hook up to our trailer, easily to get to. When we're done, we don't have to worry about having any electrical connections exposed outside of the vehicle which can corrode over time when exposed to the elements. more
6/23/2016 11:26:50 AM
Trailer Wiring Harness Installation - 2013 Chrylser 300- Video
Today on our 2013 Chrysler 300 we will be installing the Curt T-Connector Vehicle Wiring Harness with 4 Pole Flat Trailer Connector, part number C56145. When we want to use the wiring we'll just take some out of the trunk like so so we can make our connection to the trailer. Make sure we avoid the latch here and close the trunk on over it. This will keep it secure and it'll be easy to use. When you're done towing your trailer you open the trunk back up, lift up on the spare tire cover panel and store your wires just like so and have full access to your trunk; you don't have to worry about snagging the wire on anything. Here's what comes in our wiring harness package. We have our control module here, which will prevent any voltage being back fed into the vehicle's wiring harness. more
6/20/2016 3:55:22 PM
Trailer Wiring Harness Installation - 2015 Chrysler Town and Country- Video
Today on our 2015 Chrysler Town and Country, we're going to take a look at and show you how to install the tow ready T1 vehicle wiring harness with the 4 pole flat trailer connector. The part number is 118534. Now here's what the wiring harness is going to look like before we start installing it. We've got the center of the operation, which is the ModuLite. This is a module. Hooks into the battery of the vehicle using the 12 volt power chord that's provided. Also goes through a fuse holder. more
7/14/2015 11:57:32 AM
Trailer Wiring Harness Installation - 2012 Chrylser 300C- Video
Today on our 2012 Chrysler 300C, we're going to review and install the Curt T-Connector Custom Fit Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56145. Now with the Curt Custom Fit Vehicle Wiring Harness with 4-Pole Flat Trailer Connector already installed, let's go ahead and take a look at it. The 4-pole connector is going to store down with the spare tire. By storing it inside, it keeps it out of the inclement weather and prevents buildup of rust and corrosion over time. To use it, we'll simply take it out of the spare tire well and run it out over the threshold. Stay away from the latch, because pinching it off in the latch will damage the wire. However, the weather stripping is thick enough that we can simply close the rear trunk on it. Pull out the wire we need to run to our hitch or accessory, and then when we're done simply roll it up and store it back inside. more
6/10/2015 8:53:07 AM
Trailer Wiring Harness Installation - 2012 Chrysler Town and Country- Video
All right, today on this 2012 Chrysler Town & Country, we're going to show you the CURT key-connector vehicle wiring harness with a four-pull flat trailer connector, part number C56150. These are the parts that you get with the kit, a T-connector right here. This one with the yellow wire goes to the left-hand side or the driver's side, and we have a T-connector here that goes up to the right-hand side. These connections are made right behind the tail light. These two wires go down to the module here and when signal goes to the module here, it goes out to our four-pole flat. Also, our four-pole flat comes with a protective cover when you are not using it. Now our module is going to need to get power from a 12-volt power supply up-front. more
5/26/2015 3:22:09 PM
Trailer Wiring Harness Installation - 2010 Chrysler 300- Video
Today on our 2010 Chrysler 300 we're going to be installing the tow ready T1 vehicle harness with the four pull flat trailer connector its part number is 118406. Now when ready for use we'll just pull our four pull wire out, bring our cover down and over. Now when your using it pull out whatever length you need to make your connection and we'll let it rest right over the gasket. We want to avoid the latch section there, but then when you close it your gaskets going to hold that in place and give you a nice pig tail out here where you can use it. The cover over the top here can come in pretty handy, for getting this kind of tucked away we can use this as almost like a buckle or a strap for it. Get it all squeezed together real close and bring that around like that. Kind of keep it bundled up there nice little tuck in area there you wouldn't even have to tuck it in underneath. more
5/22/2015 7:57:52 AM
Trailer Wiring Harness Installation - 2014 Chrysler Town and Country- Video
Today in a 2014 Chrysler Town & Country, we're going to show you a T1 vehicle wiring harness with 4-pole flat trailer connector from Tow Ready, part number 118534. We've got our parts laid out from the box, so we'll do a little bit of show and tell. First off, what color are the lower components and the ends The T-connector with the yellow wire here, goes to a connection point that's located behind driver side tail light. The T-connector with the green wire, goes over to the same connection over on the passenger side. We have a white wire with a ring terminal. That goes through sheet metal for ground. Now this black wire here, gets connected to a 12 volt power supply, so it powers our module which copies a signal that comes from our other 2 connection points. more
4/28/2015 12:47:15 PM
Trailer Wiring Harness Installation - 2015 Chrysler Town and Country C56150- Video
Today on this 2015 Chrysler Town and Country we're going to show you the Curt T-Connector Vehicle Wiring Harness, part number C56150. We'll go ahead and show you the components that come with this part number. First off this is our wire harness here. This is our four-pole flat. This is our module right here. That takes our battery power, copies the signal and sends it out to the trailer. We have our T-connector, we're yellow for the left hand side and our T-connector with the green wire for right hand side. We have a length of wire that comes with the kit to run from our module up to the front towards the battery. Once we get to the battery our fuse holder and some zip ties and some butt connectors and ring terminal to our connections up to our battery. more
4/20/2015 1:26:35 PM
Trailer Wiring Harness Installation - 2008 Chrysler Aspen- Video
Today on this 2008 Chrysler Aspen, we're going to install part number c55597 from Curt. This is the Curt T connecter Wiring Harness. First thing we need to do is go ahead and open up the back hatch and get access behind the tail lights. There are two plastic rivets on each tail light that we have to remove so we can take off the tail light. We pull off the center with a pair of pliers, and they come right out. Then set the fasteners off to the side and we'll go ahead and pop the tail light loose. Next we need to disconnect the wire harness. more
1/20/2015 2:47:42 PM
Trailer Wiring Harness Installation - 2012 Chrysler 200- Video
Today on our 2012 Chrysler 200 we're going to be installing the Curt T-Connector Vehicle Wiring Harness with a 4-Pole Flat Trailer Connector, Part Number C56211. We'll first begin our installation by opening up the rear trunk of the vehicle. Next we're going to need to remove a few interior pieces so that we can gain access to the wiring. Since this vehicle is a convertible it is a little bit different than the sedan model. Now with our trunk linings removed, next we're going to need to remove a few other interior pieces. We'll need to remove this rear threshold piece as well as peel back the 2 plastic linings on both sides. To remove the rear threshold piece we'll simply pull up gently so that it unsnaps from its clips. more
12/19/2014 8:41:56 PM
Trailer Wiring Harness Installation - 2008 Chrysler Sebring- Video
Today on our 2008 Chrysler Sebring we will be installing the Tow Ready T-One Connector, part number 118444. To begin with you'll need to raise the trunk lid up. Next you will need to locate the two plastic nuts that are on the backside of each of the light assemblies. On this particular vehicle, since it's a convertible, we we're able to just slip our hand in behind the inner lining of the trunk and get both of the nuts removed from the rear of the light assembly. You'll need to repeat this procedure for both the driver and the passenger side. Once you have the two plastic nuts removed from the rear of the light assembly you'll gently pull the light assembly out, being sure not to break the clip off that slides into the body. Once that is out we will need to disconnect the two wire connections on the back. more
12/10/2014 8:33:46 PM
Trailer Wiring Harness Installation - 2009 Chrysler 300- Video
Today on our 2009 Chrysler 300 we'll be installing the Tow Ready T1 Vehicle wiring harness with four-pole flat trailer connector, part number 118406. To begin with, we'll go ahead and open up the trunk. Both on the driver and the passenger side, there's a small plastic wing nut that'll need to be removed and the carpet pulled back to gain access to the wiring connections. Now that we have both of these removed and the carpet pulled back some, we'll go ahead and start on the passenger side. Before we can remove the factory wiring connection, we need to pull the red tab, which is the locking tab, to the open position on the connection. With that done, we'll go ahead and squeeze the small tab and pull the connector apart. We'll open up the center section of the trunk, or lift it up, exposing the spare tire, as well as the battery. Next we'll go ahead and connect our T1 connector in-line, matching up the male and female opposite ends so that you put the T1 connection in-line for the factory harness. more
11/24/2014 4:22:04 PM
Trailer Wiring Harness Installation - 2003 Chrysler PT Cruiser- Video
Today our 2003 Chrysler PT Cruiser we'll be installing the Curt T-Connector Wiring Kit, part number C55532. To begin with we'll need to remove both tail light assemblies by removing the torxhead screw that's at the lower section on the tail light assembly. Once you pull the tail light assembly out, because careful not to break the clips off as you're removing the tail light assembly. Then we will go ahead and unplug both plugs from the rear of the assembly. On this case we used a small screw driver to help release both of the locking tabs. Once we have the passenger side light assembly out and the wires disconnected we will go ahead and drop down the 4-flat as well as the yellow wire with the connectors down through the light assembly and under the rear bumper fascia. We'll plug the grey connector that has two wires into it with the green wire into the vehicle's harness, making sure that the locking tabs snap into place. We will also make the connection with the plug that has three wires, one of them has a brown and red wire in it as well. more
11/10/2014 10:45:27 AM
Trailer Wiring Harness Installation - 2005 Chrysler 300- Video
Today on our 2005 Chrysler 300 we'll be installing the Tow Ready T-One Connector, part number 118404. We'll go ahead and show you how to use the new 4-pole connector. Well simply take the 4-pole and run it out and down to the hitch or accessory, being careful to stay away from the ledge as pinching the wire off in the ledge can harm the wire. However, the weather stripping is thick enough that it won't and we'll simply close the rear cargo door on it. Once we're finished using our new 4-pole connector, we'll roll it up and store it under the spare tire cover. To install our new 4-pole connector, we'll simply open up the rear cargo door or trunk. We'll need to access the wiring behind the driver and passenger side tail lights. Here on the passenger side we'll go ahead and remove the plastic wing nut and pull back the carpeting to gain access. more
10/27/2014 2:44:19 PM
Trailer Wiring Harness Installation - 2010 Chrysler Town and Country- Video
Today on our 2010 Chrysler Town and Country, we'll be installing the Tow Ready T-One wiring harness with 4-pole flat trailer connector, part number 118552. To begin with, we'll need to go ahead and raise the rear hatch of the vehicle as this is how you access the two screws that hold in each of the taillight assemblies for both the driver and passenger side. To remove the taillight assembly, you'll need a T30 Torx head bit. We'll go ahead and remove the two screws and then you'll need to kind of work the light assembly around a little bit as there are two more tabs up towards the front of the vehicle that need to be pulled out their housing as well. With the taillight assembly removed, we can go ahead and disconnect the wiring harness. To do this, you'll need to release the red locking tabs on each of the two connectors and squeeze the tab and gently pull the plug off of the connector. Now, we're only going to be tying into the top connector, but to make things a little easier, we're going to go ahead and remove the bottom plug as well just so we can go ahead and set our light assembly aside. We'll go ahead and repeat the same process for both the driver and the passenger side. Now, we'll go ahead and take our T-One wiring harness. more
10/6/2014 1:12:54 PM
Trailer Wiring Harness Installation - 2014 Chrysler Town and Country C56150- Video
Today on our 2014 Chrysler Town and Country, we'll be installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56150. To begin our install, first we'll open up the rear hatch and locate the fasteners that secure the rear taillight assemblies. We'll remove the fasteners and then remove the taillights. To remove the taillights, we'll simply pull them out towards the rear of the vehicle, releasing the fastener alignment pins underneath. Then to remove the taillight assembly, push up on the read locking tab to release it then press on the connector lock that remove the wiring harness from the socket. We'll set the taillight aside, move over the passenger side and repeat the same process. Now with both taillight assemblies removed, we'll go and take the new wiring harness and the yellow and brown wire connector, plug it in to the manufacturer's wiring on the driver's side. Next we'll take the 4-pole connector and green wire connector and feed it down between the bumper cover and via the vehicle. This will come out down underneath the vehicle where we can then go ahead route the green wire connector over to the passenger side and the 4-pole connector towards the center of the vehicle and ultimately to the hitch. more
9/2/2014 2:52:29 PM
Trailer Wiring Harness Installation - 2007 Chrysler Aspen- Video
Today on this 2007 Chrysler Aspen we are going to install part number 118390 from Tow Ready. First thing we need to do is go ahead and get our vehicle ready to install the wire harness. To do that we need to go ahead and open up the tail gate and get access to remove the tail lights. To remove the tail lights, well go ahead and remove these plastic fasteners with a pair of pliers grip the centres and pull it out. Now were going to remove the tail light. Well go ahead and work the bottom and top little bit and pull back. Theyll unsnap from these fasteners here. Now before we connect the wire harness, weve got to loosen up this red lock right here. more
6/17/2014 8:49:12 AM
Trailer Wiring Harness Installation - 2013 Chrysler Town and Country- Video
All right. Today on our 2013 Chrysler Town and Country, we're going to install part number C56150 from Curt. This is Curt T connector wiring harness with a 4-pole flack. First thing we need to do is get the van ready to install our wire harness. We'll go ahead and open up the back hatch and remove the tail lights. We'll need a ten millimeter socket to remove the lights. more
5/27/2014 4:08:48 PM
TowReady Taillight Converter Hardwire Kit Installation - 2001 Chrysler Sebring- Video
Today in our 2001 Chrysler Sebring convertible, we will be installing the tow-ready, upgraded circuit-protector tail light converter hardware kit with four-pole end, including a tester, part number119178KIT.To begin with here, we're going to figure out whether we have a two-wire or three-wire system on this vehicle. We'll go ahead and run through the light functions and see which bulbs come on when we turn the running lights on, the blinkers, as well as the brake lights. As you can see here with the running lights on, we get the top two bulbs, which are red here, come on on both sides. When you step on the brakes, just the two inner bulbs towards the center of the trunk come on. When we turn each blinker on, it's actually a bulb down below that's part of the clear section. With running this simple test, this tells us that we have a three wire system, so we will be using the red wire on the converter box. We will be connecting this red wire to the brake light wire. Now, let's go ahead and open up the trunk, and we'll go ahead and figure out which wires do which on the back side. We'll begin here on the driver's side. We'll go ahead and just simply peel back the inner lining of the trunk and it will expose the back of the tail light assembly, where we'll simply slide the red locking tab over and unplug the wiring harness from the back of the light assembly. more
11/5/2013 3:38:54 AM
Trailer Wiring Harness Installation - 2008 Chrysler Pacifica- Video
Today on our 2008 Chrysler Pacifica we'll be installing the Tow-ready T-One Vehicle Wiring Harness with 4-Pole Flat Connector, part number 118303.To begin our install, we'll first need to remove the rear taillights. To do this, we'll open up the rear hatch and then remove the 2 screws securing the taillight assembly. Starting on the driver's side, after we remove the screws, we'll set them aside. Using a plastic pry tool or flat-blade screwdriver, gently pry out between the housing and taillight assembly, pulling straight back from the vehicle, to release the fastener underneath, careful not to break this fastener.Next we'll remove the taillightcompletely by unlocking the red locking tab and then pressing on the connector lock, releasing the wiring harness from the taillight assembly. Now that we've removed the driver's side taillight assembly, we'll go ahead and repeat the same process on the passenger side. We'll remove the manufacturer's grommet, where the wiring runs into the body of the vehicle. After we remove the grommet from its position, take the yellow wire, pull it out along with the connector that's wrapped in the foam padding. more
10/22/2013 12:13:50 PM
Trailer Wiring Harness Installation - 2013 Chrysler Town and Country 118534- Video
Today on this 2013 Chrysler Town and Country, were going to install part number 118534. To start off our install were going to open up the back hatch and were going to remove the two taillights. Our two screws that we have to remove and then well pop them loose on the body and then well go ahead and remove the wire harness from the taillight. Theres a small red lock we have to push to unlock it and then a tab that we have to push to release it from the taillight and we can pull it apart. Well set our driver side taillight to the side and do the same thing on the passenger side.Now we can go ahead and start installing the wire harness. First off well take the four pole end and well route it between the body work and the bumper cover going down to the bottom. more
2/8/2013 2:52:29 PM
Trailer Wiring Harness Installation - 2012 Chrysler Town and Country 118534- Video
Today on our 2012 Chrysler Town & Country well be installing the Tow Ready T1 Connector, part number 118534. Now to begin our installation were going to open the rear tailgate to access the screws that hold the taillights in place. Well remove the bolts holding the taillights and carefully pry the taillight housing rearward away from the vehicle being very careful not to break the alignment tabs. Once weve removed the taillights from the vehicle we can pull the red tab here on the connector. Well then push the button and allow the connector to separate. Now here on the drivers side well take the T connector in with the yellow wire and connect it to the vehicle wiring and lock it into place. more
11/19/2012 3:17:50 PM
Trailer Wiring Harness Installation - 2009 Chrysler Town and Country- Video
Today on our 2009 Chrysler Town and Country well be installing the tow ready T1 connector, part number 118552. To start our install well first open up the rear cargo door and remove the driver side tail light housing. There are two fasteners securing the housing that we will remove first. Then well gently pry and pull the tail light assembly away from the body of the vehicle. Be careful not to break the alignment tabs as you do so. Now with our tail light assembly removed we can go ahead and unlock the red locking tab and disconnect the wiring connector from the bulb and socket. more
10/5/2012 1:17:56 PM
Filter Videos
Filter Videos
